If you ’re new to pool ownership , you may not have it off how to install a skimmer on anabove - ground pool . Perhaps the society that put in your pool in the first station also installed the skimmer and you ’ve decided you call for a fresh one . Maybe your quondam one got too cold and cracked over the frigid wintertime months . perchance you ’re just tired of pick leaves and bugs out of the pool every clip you turn around . Whatever your grounds , you ’ve decide it ’s time to get a new sailor to makecleanupeasier .
There are a few different models of pool skimmer . Always consult the instruction manual first , but the general facility instructions are the same across maker .
Below , we ’ll show you the quickest and well-heeled elbow room to install your new syndicate leghorn .
Remove the old skimmer
Of of course , before you could install your novel skimmer andreplace the liner(if that ’s what you also intend ) , you have to remove the old one .
Step 1 : Remove the old skimmer gaskets .
tone 2 : Use a drill to remove the screws around the previous Panama . This is as good a metre as any to supervene upon the screws as well .
footfall 3 : Clean the sides of the puddle wall of any debris , and get rid of any sign of calcium or rust fungus . If the bulwark is very rusty , you may need to sandpaper and thenpaint over the areawith rust fungus - proof blusher .
Begin the new skimmer installation
Once the rust - proof paint has dry is , it ’s clock time to put the sailor .
footmark 1 : Ensure that the sailor can reach all areas of the pool when extended . Be certain you get it right because displace it to a different location after installing it can be a challenge .
stair 2 : Drain the consortium a bit so that you may easily instal the skimmer without touching the water .
Install the faceplate
Once you ’ve select the right location and drained the water to an appropriate level , you need to instal the Panama ’s faceplate .
Step 1 : opt a spot for the faceplate , ideally as airless to the skimmer ’s opening as possible , and employ a mark or pen to mark the holes in the bulwark for placement .
stone’s throw 2 : employ the marks as guides to drill holes into the side of the pool .
Step 3 : Add caulking to the faceplate and press it firmly to the pool ’s side .
Add the skimmer
Once you ’ve instal the plate , it ’s time to add the Panama itself .
measure 1 : Put a level of caulking on the sharpness of the pond gaskets and pose these into the pool ’s side .
Step 2 : point the straw hat on top of the gasket .
footstep 3 : Push the screw propeller for the skimmer into the faceplate until they arrive at the gaskets on the puddle ’s side .
Step 4 : Tighten the bollock and bolts on the paired side of the faceplate . Be certain not to excessively tighten them , however , as doing so could break the faceplate .
Finish up
You ’re almost there ! Just a few more steps and your novel skimmer will be installed and quick to use .
Step 1 : habituate scissors or a abrupt knife to cautiously edit out an chess opening in the pool ’s liner at the top of the skimmer faceplate .
Step 3 : replenish the pool to its former level .
Step 4 : define up the pool pump and restart it .
Step 5 : Skim the water to ensure all the tubes and pipes are clear , and then leave the skimmer in the water until needed again .
With a little bit of solitaire and a little elbow grease , you ’ll soon have a young boater to make yourpool maintenance routinemuch gentle . And call back : sometimes it ’s overbold to instal a second straw hat on an above - undercoat pool , especially if you have a lot of Tree in the sphere that will drop leave into the H2O . Having more than one skimmer can definitely help to keep your pool clean and ready for you when you ’re ready to take a dip .
